產品詳情
Fluid意大利制造MG204XD0PT00000齒輪泵原廠現貨Fluid-o-Tech英文原版資料選型指導
Disassembly Instructions Provide a clean surface for work area. Separate the pumphead from the magnet cap. Remove the 3 screws and disassemble front housing , driven gear , central housing and dowel pins . If the pump is equipped with by-pass, make sure not to damage the sealing poppet . Remove the poppet assembly from the adjusting screw (fig. 5), remove the by-pass nut , the adjusting screw turning counter-clockwise, the by-pass washer and the by pass seal from the cap. Remove the screws which secure the magnet cup and the mounting plate to the rear housing and disassemble. Remove and discard all the bushings from the rear housing and the front housing with the bushing extractor tool P/N 60211 (fig.1). Remove seal and flat seals from the rear housing and from the front housing and discard them. If wear on front housing, rear housing or center housing is excessive, rebuilding the pump my not be advisable.
Re-Assembly Instructions Clean carefully all parts before re-assembling. Any foreign body material clinging to magnet must be removed.
Note Bushings - Bushings on both sides of gears must be recessed 0.5 mm from the face of the rear housing and front housing (fig. 2) Bushings Installation - Press 6 new bushings into the rear housing and front housing as shown in figure 2 using P/N 60212 installation tool. Once in place, the bushings need to be reamed with P/N 60210 reamer tool (fig. 3). Seals - Apply a thin coat of silicone grease on the central housing surfaces and place the flat seals on each side of it insert the driving gear into the rear housing and then insert the shaft of the driving gear in the driven magnet using the spacer P/N 60213 (fig. 4). Insert 2 dowel pins in the body. Slip carefully central housing onto dowel pins against body face, verifying the proper, alignment of the screw holes. Install the driven gear (The side of gear assembly with longer shaft extension goes into the rear housing). If pump is equipped with by-pass, install the by-pass
seal , then by-pass nut and tighten to prevent by-pass seal rotation. Then tap the by-pass seal with the P/N 60214 tool (fig. 6). Disassemble the by-pass nut and install by-pass washer and turn clockwise the adjusting screw before installing again the by-pass nut tightening. Align the cap bushing holes with gear shafts, and dowel pins with cap dowel pin holes and assemble. Make sure that the poppet assy goes fully into poppet holes and seat (fig. 5). Install 3 screws in cap and tighten alternaby as tight as possible. Turn driven magnet with fingers to check for any binding during the rotation: the magnet should turn freely. Install magnet cup and mounting plate with 3 screws and turn alternaby until tight. Assemble the driving magnet to the motor (see fig. 7) and the pumphead to the motor.
Service Kit - MG Gear Pump Stainless steel pumphead
Service kit contents 2 gears - 1 Teflon “O” ring - 2 Teflon flat seals - 6 bearings
Service kit tools 1 reamer P/N 60210 1 extractor P/N 60211 1 bushing tool P/N 60212 1 spacer P/N 60213 1 tap P/N 60214
SPARES & INSTRUCTIONS – 10/01
（1）結構簡單，價格便宜；
（2）工作要求低，應用廣泛；
（3）端蓋和齒輪的各個齒間槽組成了許多固定的密封工作腔，只能用作定量泵。
齒輪采用國際九十年代先進水平的新技術--雙圓弧正弦曲線齒型圓弧。它與漸開線齒輪相比，最突出的優點是齒輪嚙合過程中齒廓面沒有相對滑動，所以齒面無磨損、運轉平衡、無困液現象，噪聲低、壽命長、效率高。該泵擺脫傳統設計的束縛，使得齒輪泵在設計、生產和使用上進入了一個新的領域。
泵設有差壓式安全閥作為超載保護，安全閥全回流壓力為泵額定排出壓力1.5倍。也可在允許排出壓力范圍內根據實際需要另行調整。但是此安全閥不能作減壓閥長期工作，減壓閥在需要時可另行安裝。
該泵軸端密封設計為兩種形式，一種是機械密封，另一種是填料密封，可根據具體使用情況和用戶要求確定。
齒輪泵泵的分類
就核心組成部件齒輪而言，主要由公法線齒輪泵和圓弧齒輪泵。公法線齒輪泵輸送含雜質的介質比圓弧齒輪泵要耐用，而圓弧齒輪泵結構特殊，輸送干凈的介質，噪音低，壽命長，各有各的優點。
MG204XD0PT
MG204XD0TT
MG204XD0GT
MG204XD1PT
MG204XG0PT
MG204XG0TT
MG204XG0GT
MG204XG1PT
MG204SG0PT
MG204SG0TT
MG204SG0GT
MG204SG1PT
MG204SG1TT
MG204SG1GT
MG204YD1PT
MG204YD1TT
MG204YD1GT
MG204YG0PT
MG204YG0TT
MG204YG0GT
MG209XD0PT
MG209XD0PT
MG209XD0TT
MG209XD0GT
MG209XD1PT
MG209XD1TT
MG209XD1GT
MG209XG1PT
MG209XG1TT
MG209XG1GT
MG209XG0PT
MG209XG0TT
MG209XG0GT
MG209SD0PT
MG209SD0TT
MG209SD0GT
MG209SD1PT
MG209SD1TT
MG209SD1GT
MG209SD1PT
MG209SG1PT
MG209SG1TT
MG209SG1GT
MG209SG0PT
MG209SG0TT
MG209SG0GT
MG209YD0PT
MG209YD0TT
MG209YD0GT
MG209YD1PT
MG209YD1TT
MG209YD1GT
MG213XD0PT
MG213XD0GT
MG213XD0TT
MG213XD1PT
MG213XD1TT
MG213XD1GT
MG213XG0PT
MG213XG0GT
MG213XG0TT
MG213XG1PT
MG213XG1TT
MG213XG1GT
MG213SD0PT
MG213SD0TT
MG213SD0GT
MG213SD1PT
MG213SD1TT
MG213SD1GT
MG213SG0PT
MG213SG0TT
MG213SG0GT
MG213SG1PT
MG213SG1TT
MG213SG1GT
MG213YD0PT
MG213YD0TT
MG213YD0GT
MG213YD1PT
MG213YD1TT
MG213YD1GT
MG213YG0PT
MG213YG0TT
MG213YG0GT
MG213YG1PT
MG213YG1TT
MG213YG1GT
MG217XD0PT
MG217XD0TT
MG217XD0GT
MG217XD1PT
MG217XD1TT
MG217XD1GT
MG217XG0PT
MG217XG0TT
MG217XG0GT
MG217SD0PT
MG217SD0TT
MG217SD0GT
MG217SD1PT
MG217SD1TT
MG217SD1GT
MG217SG1PT
MG217SG1TT
MG217SG1GT
MG217YD0PT
MG217YD0TT
MG217YD0GT
MG217YD1PT
MG217YD1TT
MG217YD1GT
MG217YG0PT
MG217YG0GT
MG217YG0TT
MG217YG1PT
MG217YG1TT
MG217YG1GT
MS204XD0PT
MS204XD0TT
MS204XD0GT
MS204XD1PT
MS204XG0PT
MS204XG0TT
MS204XG0GT
MS204XG1PT
MS204SG0PT
MS204SG0TT
MS204SG0GT
MS204SG1PT
MS204SG1TT
MS204SG1GT
MS204YD1PT
MS204YD1TT
MS204YD1GT
MS204YG0PT
MS204YG0TT
MS204YG0GT
MS209XD0PT
MS209XD0PT
MS209XD0TT
MS209XD0GT
MS209XD1PT
MS209XD1TT
MS209XD1GT
MS209XG1PT
MS209XG1TT
MS209XG1GT
MS209XG0PT
MS209XG0TT
MS209XG0GT
MS209SD0PT
MS209SD0TT
MS209SD0GT
MS209SD1PT
MS209SD1TT
MS209SD1GT
MS209SD1PT
MS209SG1PT
MS209SG1TT
MS209SG1GT
MS209SG0PT
MS209SG0TT
MS209SG0GT
MS209YD0PT
MS209YD0TT
MS209YD0GT
MS209YD1PT
MS209YD1TT
MS209YD1GT
MS213XD0PT
MS213XD0GT
MS213XD0TT
MS213XD1PT
MS213XD1TT
MS213XD1GT
MS213XG0PT
MS213XG0GT
MS213XG0TT
MS213XG1PT
MS213XG1TT
MS213XG1GT
MS213SD0PT
MS213SD0TT
MS213SD0GT
MS213SD1PT
MS213SD1TT
MS213SD1GT
MS213SG0PT
MS213SG0TT
MS213SG0GT
MS213SG1PT
MS213SG1TT
MS213SG1GT
MS213YD0PT
MS213YD0TT
MS213YD0GT
MS213YD1PT
MS213YD1TT
MS213YD1GT
MS213YG0PT
MS213YG0TT
MS213YG0GT
MS213YG1PT
MS213YG1TT
MS213YG1GT
MS217XD0PT
MS217XD0TT
MS217XD0GT
MS217XD1PT
MS217XD1TT
MS217XD1GT
MS217XG0PT
MS217XG0TT
MS217XG0GT
MS217SD0PT
MS217SD0TT
MS217SD0GT
MS217SD1PT
MS217SD1TT
MS217SD1GT
MS217SG1PT
MS217SG1TT
MS217SG1GT
MS217YD0PT
MS217YD0TT
MS217YD0GT
MS217YD1PT
MS217YD1TT
MS217YD1GT
MS217YG0PT
MS217YG0GT
MS217YG0TT
MS217YG1PT
MS217YG1TT
MS217YG1GT
